New
TEKTON 1/4 Inch Aluminum Handle Bit Driver and Security Insert Bit Set with Case (38-Piece)
Front-right angle view of Tekton case bit set. Item #DBA93102
Laid out contents of Tekton case bit set. Item #DBA93102
Side view of Tekton case bit set. Item #DBW93101
Person holding Tekton case bit set. Item #DBW93101
Tap image to zoom in
Item #DBA93102
1/4 Inch Hex Shank
1.18 Inch Bit Length

Aluminum Handle Bit Driver and Security Insert Bit Set with Case (38-Piece)

Tamper Star T7 - T30
Tamper Hex 5/64 - 1/4 in., 2 - 6 mm
Clutch 1/8 - 1/4 in.
Spanner #4 - #10
•

Grip Type

Aluminum
$40
Molded
$35
$40.00
Add to Cart
Set Includes:
DetailsSpecifications

Details

Video Overview

This set contains a magnetic bit driver with 36 bits for the most common security fastener types and sizes. Bits are held in 9-tool rails with clear size markings, and they are easy to remove. The soft-shell zipper case is compact and portable. The open lid serves as a parts tray.

Bits with Rails

A typical bit is 0.98 inches, a Tekton bit is 1.18 inches

Slightly Longer Than Typical Insert Bits

A graphic showing a #4 spanner bit turning a recessed slotted screw.

Low Shoulders for Recessed Screws


For small tip sizes, the shoulders on the hex shank are reduced as low as possible, keeping the shaft diameter narrow so it can reach into tight, recessed areas.


Close-up image of the tip of a tamper star bit.

Hardened Steel with Precise Tip Geometry


The bits are made of S2 tool steel and are through-hardened to 58 - 61 HRC. Tight tolerances on the tip geometry keep the bit seated in the screw, reducing slip and wear.


A T20 tamper star bit being removed from a rail.

Stamped Markings and Satin Finish


The tip size is permanently stamped onto every bit in large, clear type. A zinc-phosphate coating adds a satin finish that resists corrosion.

Free-Standing Bit Rails


The flexible rails securely grip the bits so they can’t fall out, while also making it easy to remove any bit one-handed. The rails can also stand upright on a surface.


Sizes are printed on the rails for easy identification

Sizes are printed on the rails for easy identification

A bit being removed from the rail. Set #DZZ93016 is shown.

Magnetic Bit Driver with Aluminum Handle

Two hands spinning a bit driver

Coarse Knurling and Rounded Areas for Better Grip and Faster Spinning

A deep, sharp-cut diamond pattern is knurled into the rounded sections at the front and back of the handle to create a coarse, non-slip texture.
Close-up image of the knurling on a bit driver
Close-up image of the 1/4 inch drive square on the end of the aluminum handle

1/4 Inch Drive Square in the Handle

Add a ratchet for extra leverage to break a fastener loose, then pull the ratchet off and spin the driver to run it out. Swap in a torque wrench to tighten to spec.
Image of a hand putting a ratchet on the drive square

Magnetic Bit Holder


Bits are held securely by a magnet that is permanently press-fit and cannot come out.


A 1.18 inch bit extends 0.79 inches beyond the driver, and a 0.75 inch bit extends 0.36 inches beyond the driver.
Graphic of a cutaway of the bit driver, showing the magnet
An aluminum handle bit driver in use

3.2 Inch Blade Length

The exposed blade is similar to a standard screwdriver length and extends your reach into tight spaces.
Graphic showing the exposed blade of the bit driver is 3.2 inches long

Compact Carrying Case

The case has contoured EVA foam, durable 3-layer material, and zippered closure

Specifications

1/4 Inch Aluminum Handle Bit Driver and Security Insert Bit Set with Case (38-Piece)

Specs for 1/4 Inch Aluminum Handle Bit Driver and Security Insert Bit Set with Case (38-Piece)
Country of Origin
Taiwan
Item Weight
1.1 lb.